Product Carousel Tabs
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional spool valve type WH is intended for
change in direction of fluid flow in a hydraulic system
and thus it allows changing the direction of movement of
a receiver – mostly piston rod of a cylinder or
hydraulic motor as well to use functions: on and off.
This directional spool valve is used for subplate
mounting in any position in a hydraulic system.
Multiple Sizes available:
NG 16 Up to 240 L/min
NG 22 Up to 450 L/min
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Pilot operated double-check valve type Z2S serves to
shut-off an oil flow in one direction and allow free flow in
the opposite direction. They can also be opened in the
direction of closure.
These valves are mostly used :
– to relieve a working circuit under pressure
– to prevent a load from falling in the case of a line rupture
– to prevent creep movements of hydraulically stressed users.
These valves are generally fitted as an intermediate element between the control valve and the subplate. Sealing
of interfaces is provided by o-rings, which are included.
The valve can be installed in any position
Sandwich Throttle Valve with Bypass – Ponar Wadowice
Sandwich Throttle Valve with Bypass – Ponar Wadowice
Throttle/check valve type Z2FS… is used to control main flow rate (or pilot
flow rate) in one direction and to allow free flow in the opposite direction.
The valve may be designed as double version (valve function is realized in
two ports A and B) or single version (valve function is realized in one port
A or B). The valve is applied to sandwich plate mounting.
Subplate Relief valve – Ponar Wadowice
Pressure relief valves type DB…DB… serve to limit pressure
in a hydraulic system or in its part, while in version
DBW… with pilot valve it is also used to unload
pressure in a system. Application example:
•DB… for setting up maximum pressure in a system
•DBW… for actuation of a pump without pressure
Direct Operated Sandwich Relief Valve – Ponar Wadowice
Direct Operated Sandwich Relief Valve – Ponar Wadowice
The pressure relief valve, sandwich plate design type UZPR6… is used to
limit pressure in hydraulic systems. The valve is suitable for sandwich plate
mounting in any working position
Direct Operated Cartridge Relief Valve – Ponar Wadowice
Direct Operated Cartridge Relief Valve – Ponar Wadowice
A direct operated pressure relief valve type DBD… is
designed to limit maximum pressure in the entire
hydraulic system or in its part. Depending on the type
of mounting in the system, the pressure relief valve
type DBD… can be screwed (cartridge version),
mounted into threaded connections (version for
threaded connection) or mounted to subplate (version
for subplate mounting).
Directional Control Valve Manual Control – Ponar Wadowice
Directional Control Valve Manual Control – Ponar Wadowice
Directional spool valves are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off
Directional Control Valve – Electrically Controlled
Directional Control Valve – Electrically Controlled
Directional spool valves type WE electrically operated are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change the direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off. These directional spool valves are used for subplate mounting in any position in a hydraulic system.
Multiple Electrical Options
12VDC
24VDC
110VAC
220VAC
Multiple Sizes
NG 6 Up to 80 L/min
NG 10 Up to 160 L/min
Direct Operated Sandwich Relief Valve – Ponar Wadowice
Direct Operated Sandwich Relief Valve – Ponar Wadowice
The pressure relief valve, sandwich plate design type UZPR6… is used to
limit pressure in hydraulic systems. The valve is suitable for sandwich plate
mounting in any working position
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional spool valve type WH is intended for
change in direction of fluid flow in a hydraulic system
and thus it allows changing the direction of movement of
a receiver – mostly piston rod of a cylinder or
hydraulic motor as well to use functions: on and off.
This directional spool valve is used for subplate
mounting in any position in a hydraulic system.
Multiple Sizes available:
NG 16 Up to 240 L/min
NG 22 Up to 450 L/min
Directional Control Valve Manual Control – Ponar Wadowice
Directional Control Valve Manual Control – Ponar Wadowice
Directional spool valves are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off
Quick Fit Port IAC – Metalwork
The compressed air quick-fit coupling by Metal Work allows quick
replacement of pneumatic equipment (drills, milling machines, screwers
and actuators in general) without having to set the line pressure to zero
each time. Rapid tool changeover can be easily obtained by fitting
a female body on the branch under pressure and the male coupling
on the actuator. The presence of a female coupling with a safety valve on
the branch under pressure prevents air dispersion during disconnection.
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Pilot operated double-check valve type Z2S serves to
shut-off an oil flow in one direction and allow free flow in
the opposite direction. They can also be opened in the
direction of closure.
These valves are mostly used :
– to relieve a working circuit under pressure
– to prevent a load from falling in the case of a line rupture
– to prevent creep movements of hydraulically stressed users.
These valves are generally fitted as an intermediate element between the control valve and the subplate. Sealing
of interfaces is provided by o-rings, which are included.
The valve can be installed in any position
Flow Micro Regulator – MetalWork
Main features:
• reduced dimensions
• excellent regulation
• regulation with a screwdriver and disposable anti-tampering cap (COMPACT O)
• regulation with either a screwdriver and/or a knob, can be fixed with a ring nut (COMPACT N)
• available in all sizes (from M5 to G1/2) with a brass or a techno polymer ring
• available (from 10-32 UNF to 1/2 NPT) only with brass ring version COMPACT N
• can be mounted with an automatic screwdriver
• comes with a ring that can rotate even with the MRF mounted in position
Direct Operated Cartridge Relief Valve – Ponar Wadowice
Direct Operated Cartridge Relief Valve – Ponar Wadowice
A direct operated pressure relief valve type DBD… is
designed to limit maximum pressure in the entire
hydraulic system or in its part. Depending on the type
of mounting in the system, the pressure relief valve
type DBD… can be screwed (cartridge version),
mounted into threaded connections (version for
threaded connection) or mounted to subplate (version
for subplate mounting).
Direct Operated Cartridge Relief Valve – Ponar Wadowice
Direct Operated Cartridge Relief Valve – Ponar Wadowice
A direct operated pressure relief valve type DBD… is
designed to limit maximum pressure in the entire
hydraulic system or in its part. Depending on the type
of mounting in the system, the pressure relief valve
type DBD… can be screwed (cartridge version),
mounted into threaded connections (version for
threaded connection) or mounted to subplate (version
for subplate mounting).
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Pilot operated double-check valve type Z2S serves to
shut-off an oil flow in one direction and allow free flow in
the opposite direction. They can also be opened in the
direction of closure.
These valves are mostly used :
– to relieve a working circuit under pressure
– to prevent a load from falling in the case of a line rupture
– to prevent creep movements of hydraulically stressed users.
These valves are generally fitted as an intermediate element between the control valve and the subplate. Sealing
of interfaces is provided by o-rings, which are included.
The valve can be installed in any position
Directional Control Valve Manual Control – Ponar Wadowice
Directional Control Valve Manual Control – Ponar Wadowice
Directional spool valves are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional spool valve type WH is intended for
change in direction of fluid flow in a hydraulic system
and thus it allows changing the direction of movement of
a receiver – mostly piston rod of a cylinder or
hydraulic motor as well to use functions: on and off.
This directional spool valve is used for subplate
mounting in any position in a hydraulic system.
Multiple Sizes available:
NG 16 Up to 240 L/min
NG 22 Up to 450 L/min
Direct Operated Sandwich Relief Valve – Ponar Wadowice
Direct Operated Sandwich Relief Valve – Ponar Wadowice
The pressure relief valve, sandwich plate design type UZPR6… is used to
limit pressure in hydraulic systems. The valve is suitable for sandwich plate
mounting in any working position
Sandwich Throttle Valve with Bypass – Ponar Wadowice
Sandwich Throttle Valve with Bypass – Ponar Wadowice
Throttle/check valve type Z2FS… is used to control main flow rate (or pilot
flow rate) in one direction and to allow free flow in the opposite direction.
The valve may be designed as double version (valve function is realized in
two ports A and B) or single version (valve function is realized in one port
A or B). The valve is applied to sandwich plate mounting.
Subplate Relief valve – Ponar Wadowice
Pressure relief valves type DB…DB… serve to limit pressure
in a hydraulic system or in its part, while in version
DBW… with pilot valve it is also used to unload
pressure in a system. Application example:
•DB… for setting up maximum pressure in a system
•DBW… for actuation of a pump without pressure
Standard Fittings – Metalwork
A Series
B Series
C Series
D Series
Quick Exhaust Valve VSR – Metalwork
New, more compact and lighter version.
Used to evacuate air in the cylinder quickly, which increases cylinder speed.
• Temperature 0-80°C (32°-176°F)
• Max. pressure 12 bar (1200 KPa)
• Min. pressure 0.5 bar (50 KPa)
Direct Operated Sandwich Relief Valve – Ponar Wadowice
Direct Operated Sandwich Relief Valve – Ponar Wadowice
The pressure relief valve, sandwich plate design type UZPR6… is used to
limit pressure in hydraulic systems. The valve is suitable for sandwich plate
mounting in any working position
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional Control Valve – Hydraulically Controlled – Ponar Wadowice
Directional spool valve type WH is intended for
change in direction of fluid flow in a hydraulic system
and thus it allows changing the direction of movement of
a receiver – mostly piston rod of a cylinder or
hydraulic motor as well to use functions: on and off.
This directional spool valve is used for subplate
mounting in any position in a hydraulic system.
Multiple Sizes available:
NG 16 Up to 240 L/min
NG 22 Up to 450 L/min
Directional Control Valve Manual Control – Ponar Wadowice
Directional Control Valve Manual Control – Ponar Wadowice
Directional spool valves are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off
Quick Fit Port IAC – Metalwork
The compressed air quick-fit coupling by Metal Work allows quick
replacement of pneumatic equipment (drills, milling machines, screwers
and actuators in general) without having to set the line pressure to zero
each time. Rapid tool changeover can be easily obtained by fitting
a female body on the branch under pressure and the male coupling
on the actuator. The presence of a female coupling with a safety valve on
the branch under pressure prevents air dispersion during disconnection.
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Sandwich Pilot – Operated Check Valve – Ponar Wadowice
Pilot operated double-check valve type Z2S serves to
shut-off an oil flow in one direction and allow free flow in
the opposite direction. They can also be opened in the
direction of closure.
These valves are mostly used :
– to relieve a working circuit under pressure
– to prevent a load from falling in the case of a line rupture
– to prevent creep movements of hydraulically stressed users.
These valves are generally fitted as an intermediate element between the control valve and the subplate. Sealing
of interfaces is provided by o-rings, which are included.
The valve can be installed in any position
Flow Micro Regulator – MetalWork
Main features:
• reduced dimensions
• excellent regulation
• regulation with a screwdriver and disposable anti-tampering cap (COMPACT O)
• regulation with either a screwdriver and/or a knob, can be fixed with a ring nut (COMPACT N)
• available in all sizes (from M5 to G1/2) with a brass or a techno polymer ring
• available (from 10-32 UNF to 1/2 NPT) only with brass ring version COMPACT N
• can be mounted with an automatic screwdriver
• comes with a ring that can rotate even with the MRF mounted in position
Direct Operated Cartridge Relief Valve – Ponar Wadowice
Direct Operated Cartridge Relief Valve – Ponar Wadowice
A direct operated pressure relief valve type DBD… is
designed to limit maximum pressure in the entire
hydraulic system or in its part. Depending on the type
of mounting in the system, the pressure relief valve
type DBD… can be screwed (cartridge version),
mounted into threaded connections (version for
threaded connection) or mounted to subplate (version
for subplate mounting).
Week Deals limited, Just now
Push-in-Fittings – Metalwork
Quick and easy to use, the Metal Work push-in fitting can be re-used thousands of times without affecting the pneumatic and mechanical seal in any way. It comes in various configurations and guarantees virtually unlimited, highly flexible use. The clamping spring with its special shape grips the pipe without scratching or deforming it.
These fittings are designed to facilitate pipe release. You only need to press the release bushing to open up the clamping spring and free the pipe. When you press your finger onto the release bushing, you can clearly hear the characteristic “click-clock” sound.
In the fittings, the release bushing has patented screwdriver slots to facilitate release in applications not accessible to the fingers.
Configurations RL19, RL21, RL22, RL23, RL23M, RL24, RL44, and RL49 (except for Ø5), have a ring for fixing to the wall asymmetrically in order to contain the head of a screw within the overall dimensions of the fitting. There are push-in fittings for metric pipes in the diameter range of
3 to 14, and push-in fittings for inch pipes in the diameter range of 1/8 to 1/2.
Threaded connections have ISO 228-1G cylindrical thread in the 1/8-1/2 range, ISO 7-1 conical thread in the 1/8-1/2 range, metric thread in the M3 to M12x1.5 range, and conical thread compatible with NPT female threading.
Standard Fittings – Metalwork
A Series
B Series
C Series
D Series
Quick Fit Port IAC – Metalwork
The compressed air quick-fit coupling by Metal Work allows quick
replacement of pneumatic equipment (drills, milling machines, screwers
and actuators in general) without having to set the line pressure to zero
each time. Rapid tool changeover can be easily obtained by fitting
a female body on the branch under pressure and the male coupling
on the actuator. The presence of a female coupling with a safety valve on
the branch under pressure prevents air dispersion during disconnection.
Quick Exhaust Valve VSR – Metalwork
New, more compact and lighter version.
Used to evacuate air in the cylinder quickly, which increases cylinder speed.
• Temperature 0-80°C (32°-176°F)
• Max. pressure 12 bar (1200 KPa)
• Min. pressure 0.5 bar (50 KPa)
Flow Micro Regulator – MetalWork
Main features:
• reduced dimensions
• excellent regulation
• regulation with a screwdriver and disposable anti-tampering cap (COMPACT O)
• regulation with either a screwdriver and/or a knob, can be fixed with a ring nut (COMPACT N)
• available in all sizes (from M5 to G1/2) with a brass or a techno polymer ring
• available (from 10-32 UNF to 1/2 NPT) only with brass ring version COMPACT N
• can be mounted with an automatic screwdriver
• comes with a ring that can rotate even with the MRF mounted in position
Directional Control Valve – Electrically Controlled
Directional Control Valve – Electrically Controlled
Directional spool valves type WE electrically operated are intended for change in direction of fluid flow in a hydraulic system and thus it allows to change the direction of movement of a receiver – mostly piston rod of a cylinder or hydraulic motor as well to use functions: on and off. These directional spool valves are used for subplate mounting in any position in a hydraulic system.
Multiple Electrical Options
12VDC
24VDC
110VAC
220VAC
Multiple Sizes
NG 6 Up to 80 L/min
NG 10 Up to 160 L/min
Bi-directional Stop Valve – Metal Work
Stop valves mounted on the cylinder inlets allow a flow of air only in the presence of a pneumatic pilot.
Unidirectional and bidirectional versions are available.
This item is mainly used as a safety valve. When pressure drops in the pneumatic pilot, all cylinder movement is halted
Shop online
-
Accessories, Fittings, Pneumatic, Standard Fittings
Standard Fittings – Metalwork
A Series
-
- A1 – Parallel Nipple
- A2 – Conical Nipple
- A3 – Sleeve
- A4 – Conical Reducer
- A4/Z – Parallel Reducer
- A5 – Conical Reducer
- A5/Z – Parallel Reducer
- A6 – Reducer
- A7 – Plug with Embedded Hexagon
- A8 – Nub
- A9 – Female Elbow
- A10 – Elbow Male / Female
- A11 – Female T
- A12 – Central Male T
- A13 – Lateral Male T
- A14 – Equal Female Cross
- A15 – Male Elbow
- A16 – Male T
- A17 – Central Female T
- A18 – Lateral Female T
- A19 – Parallel Hose adaptor
- A20 – Equal Cross Male / Female
- A21 – T Cross
- A23 – Y Female 90
- A24 – Y Male 90
- A25 – Extension
B Series
-
- B1 – Straight Male Conical
- B2 – Straight Female
- B3 – Straight Connector
- B4 – Bulk Head Connector
- B5 – Elbow Male
- B6 – Elbow Female
- B7 – T Central Male
- B8 – T Lateral Male
- B9 – T Male
- B10 – Nut
- B11 – Olive
- B12 – Internal Bush
C Series
-
- C1 – Straight Male Conical
- C1/Z – Parallel Straight Male with ORing
- C1/C – Straight Male with Metric Thread
- C2 – Straight Female
- C3 – Straight Connector
- C4 – Bulkhead Connector
- C5 – Male Conical Elbow
- C5/F – Elbow Female
- C6 – Elbow Connector
- C7 – Central Male T
- C8 – Lateral Male T
- C9 – T Connector
- C10 – Nut
- C11 – Equal Cross Connector
D Series
-
- D5 – Single Banjo Body
- D6 – Double Banjo Body
- D7 – Banjo Stem Single
- D8 – Banjo Stem Double
- D9 – Banjo Passing Through Single
- D10 – Banjo Passing Through Double
- D12 – Single Banjo Passing Through body
- D17 – Single Banjo with B interface
SKU: n/a -
-
Accessories, Fittings, Pneumatic, Push-in-Fittings
Push-in-Fittings – Metalwork
Quick and easy to use, the Metal Work push-in fitting can be re-used thousands of times without affecting the pneumatic and mechanical seal in any way. It comes in various configurations and guarantees virtually unlimited, highly flexible use. The clamping spring with its special shape grips the pipe without scratching or deforming it.
These fittings are designed to facilitate pipe release. You only need to press the release bushing to open up the clamping spring and free the pipe. When you press your finger onto the release bushing, you can clearly hear the characteristic “click-clock” sound.
In the fittings, the release bushing has patented screwdriver slots to facilitate release in applications not accessible to the fingers.Configurations RL19, RL21, RL22, RL23, RL23M, RL24, RL44, and RL49 (except for Ø5), have a ring for fixing to the wall asymmetrically in order to contain the head of a screw within the overall dimensions of the fitting. There are push-in fittings for metric pipes in the diameter range of
3 to 14, and push-in fittings for inch pipes in the diameter range of 1/8 to 1/2.Threaded connections have ISO 228-1G cylindrical thread in the 1/8-1/2 range, ISO 7-1 conical thread in the 1/8-1/2 range, metric thread in the M3 to M12x1.5 range, and conical thread compatible with NPT female threading.
SKU: n/a -
Accessories, Flow Micro Regulator, Pneumatic
Flow Micro Regulator – MetalWork
Main features:
• reduced dimensions
• excellent regulation
• regulation with a screwdriver and disposable anti-tampering cap (COMPACT O)
• regulation with either a screwdriver and/or a knob, can be fixed with a ring nut (COMPACT N)
• available in all sizes (from M5 to G1/2) with a brass or a techno polymer ring
• available (from 10-32 UNF to 1/2 NPT) only with brass ring version COMPACT N
• can be mounted with an automatic screwdriver
• comes with a ring that can rotate even with the MRF mounted in positionSKU: n/a -
Accessories, Auxiliary Valves, Pneumatic
Quick Fit Port IAC – Metalwork
The compressed air quick-fit coupling by Metal Work allows quick
replacement of pneumatic equipment (drills, milling machines, screwers
and actuators in general) without having to set the line pressure to zero
each time. Rapid tool changeover can be easily obtained by fitting
a female body on the branch under pressure and the male coupling
on the actuator. The presence of a female coupling with a safety valve on
the branch under pressure prevents air dispersion during disconnection.SKU: n/a -